اقدم لكم مجموعة من البرامج المفيدة
وحجمها صغير جدا على فوائدها البرنامج الاول
Air
وصف البرنامج
Air is the software to calculate wet air composition, mole weight, wet bulb temperature, absolute humidity, enthalpy and moisture dew point of flue gas, for user input of atmospheric pressure, dry bulb temperature, relative humidity and enthalpy reference temperature.
Wet air composition is calculated based on the US standard dry air composition
صورة للبرنامج
رابط البرنامج
او
http://www.4shared.com/file/73224652...ified=d2e9923a البرنامج الثانى
Flue Gas
وصف البرنامج
FlueGas is the software to calculate the mole weight, enthalpy, sulfuric dew point, moisture dew point of flue gas.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73225615...ified=d2e9923a البرنامج الثالث
Pump sizing software
وصف البرنامج
Calculation of pump capacity and pump head, i.e. pump sizing, is one of basic calculation in power plant engineering as well as other plant engineering. The pump sizing does not require sophisticate knowledge, but it is complicate calculation that may cause human errors. Therefore, pump sizing normally done using computer software, and ES_Pump_SM is the software.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73238021...ified=d2e9923a
البرنامج الرابع
Pump Power
وصف البرنامج
PumpPower is the software to calculate the pump BHP, motor rating and motor input power from the pump capacity, pump head and pump efficiency the user inputs.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73572469...ified=d2e9923a
البرنامج الخامس
Heat Transfer Calculation
وصف البرنامج
The heat transfer calculation of thermal insulation does not represented by complicate equations. The calculation consists of the calculations of conduction through insulation and the calculation of radiation/convection over the insulation surface, and is to find the insulation surface temperature at which the heat transfer rates of the two calculations are same.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73233895...ified=d2e9923a
البرنامج السادس
Line Size
وصف البرنامج
Pipe line sizing is one of the most frequent calculation in P&ID ( Piping & Instrumentation Diagram) preparation work in power plant engineering. At the beginning of P&ID preparation, the sizes of all pipe lines are selected first by velocities, while the pipe sizes of major pipe lines such as main steam line, hot reheat line, etc. are finally selected by the pressure drops specified for respective pipe lines.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73234522...ified=d2e9923a
البرنامج السابع
Steam water properties
وصف البرنامج
Stable is the program to get steam or water properties from a built-in data base prepared by ENGSoft Inc. according to IFC Formulation for Industrial Use(1967). The program does not calculate the properties by equations, but find out neighboring properties and calculate the properties wanted by interpolation as engineers normally do with steam table book.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73239750...ified=d2e9923a البرنامج الثامن
Cas Drain
وصف البرنامج
CasDrain is the program to analyze cascade heater drain piping system. Cascade heater drain piping system analysis is separated into two for discontinuity of analysis at LCV. One is the upstream piping of heater level control valve(LCV) and the other is the downstream piping of LCV. For proper operation of LCV and drain system, the upstream flow should not have flashing, while the downstream piping allows flashing.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73233043...ified=d2e9923a
البرنامج التاسع
Safety valve vent stack analysis
وصف البرنامج
SVVent is the program to analyze safety valve vent stack.. ES_SVVent has functions to analyze both open and closed discharge type vent stacks. Discharge elbow of safety valve is also analyzed as a separate piping in case of open discharge type, while the discharge elbow of closed discharge type is analyzed as an integral piping of vent stack. Other auxiliary calculations are also performed simultaneously, such as reaction forces, preliminary reaction forces of closed type during initial blow. etc.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73239265...ified=d2e9923a
البرنامج العاشر
Blow Out
وصف البرنامج
BlowOut is the program to analyze steam blow-out piping system. The program has two functions for calculation category. One is Design Calculation and the other is Field Calculation.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73232363...ified=d2e9923a
البرنامج الحادى عشر
Pressure drop calculation
وصف البرنامج
Pressure drop calculation is one of the most frequent calculation in power engineering encompassing the pressure drop calculation of main steam piping having critical effect to power plant performance, through sump pump head calculation having no effect to power plant performance but important for successful operation of sump pump system.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73236374...ified=d2e9923a
البرنامج الثانى عشر
Pipe dimensions
وصف البرنامج
PSel is a derivative program of which algorithm is used in ES_PipeIso programs for user selection interface of pipe dimensions. The program shows the inside diameter, thickness and outside diameter of pipes up to 48 inch nominal diameter and various schedules in accordance with ASME/ANSI B36.10 and B36.19, BS 1600 Part 2.
صورة من البرنامج
رابط البرنامج
او
[URL="http://www.4shared.com/file/73235382/73f0ef65/Pipe_dimensions.html?dirPwdVerified=d2e9923a"]http://www.4shared.com/file/73235382/73f0ef65/Pipe_dimensions.html?dirPwdVerified=d2e9923a[/URL
البرنامج الثالث عشر
Analysis of steam flow at pipe
وصف البرنامج
StmNzle and StmPipe are the programs to verify the effectiveness of the compressible flow analysis method of steam developed by ENGSoft Inc.
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73231526...ified=d2e9923a
البرنامج الرابع عشر
Analysis of steam flow at nozzle
وصف البرنامج
StmNzle and StmPipe are the programs to verify the effectiveness of the compressible flow analysis method of steam developed by ENGSoft Inc
صورة من البرنامج
رابط البرنامج
او
http://www.4shared.com/file/73640202...ified=d2e9923a
البرنامج الخامس عشر
Unit conversion
رابط البرنامج
http://www.4shared.com/file/73640455...ified=d2e9923a 
]
هدية من الهدايا لميكانيكا بور 
العرض العادي
